Directory: A-Z
Features
INDI QSI should be able to support all Quantum Scientific Imaging (QSI) 500/600 family of cameras & filter wheels in addition to autoguiding support, whenever applicable.
Operation
Once you're connected, you can capture images as F ...
Read More...
Features
INDI QSI should be able to support all Quantum Scientific Imaging (QSI) 500/600 family of cameras & filter wheels in addition to autoguiding support, whenever applicable.
Operation
Once you're connected, you can capture images as FITS from ...
Read More...
Features
The driver supports Quantum Electronic Filter Wheel 7 x 1.25" / 2". It provides filter position control, assigning unique names for each filter and joystick control.
Operation
The filter wheel uses USB serial port, which is /dev/ttyACM ...
Read More...
Features
Rainbow Astro RSF is a secondary mirror focuser with a stepper motor. It includes a physical remote controller that can be used without a computer.
Main Control
Please note the range for the RSF focuser is -8000 to +8000 with z ...
Read More...
Installation
RPI Camera Driver currently supports the Raspberry Pi High Quality Camera in full raw mode.
Under Ubuntu, you can install the driver via:
sudo add-apt-repository ppa:mutlaqja/ppa
sudo apt-get update
sudo apt-get install indi-rpicam ...
Read More...
Features
The driver supports capture and gain adjustment. The image returned in FITS format is in Bayer BGGR 16 unsigned raw format. Currently with a fixed size of 4056x3040.
To capture a single-frame image, simply set the desired exposure time in se ...
Read More...
The Raspberry Pi GPIO driver allows you to control up to five GPIO pins on a Raspberry Pi. Typically, each GPIO pin is connected to an opto-isolator circuit or Raspberry Pi hat to control larger voltages and currents.
The driver uses the pigpio library a ...
Read More...
Features
RB Focuser is a budget-friendly telescope electronic focuser with a resolution of 0.7 microns, made to keep up with today's fast optics standard. Depending on the version, it comes with: temperature sensor, Auto home function, BlueTooth conne ...
Read More...
Features
The nFOCUS controller is a small DC focus controller that provides two directions at two speeds with only two buttons using a12V regulated output. Low speed is adjustable pulse width modulated (PWM) drive, providing full voltage torque for low s ...
Read More...
Features
The Seletek Aramadillo and Playtubus controllers support control for focuser, rotator, and filter wheels. Therefore, any stepper motor can be configured to act as a rotator. There is no primary difference between a focuser and a rotator when us ...
Read More...
Features
The nStep controller is a small absolute-position stepper motor controller that can work on a variety of motor configurations. It connects to your PC/StellarMate either via Serial-to-USB cable or WiFi. It supports the following features:
Spe ...
Read More...
Features
The settings of the RoboFocus device are polled and displayed in the corresponding fields. Main Control Tab
Port: Set the name of the RS 232 port. The speed is fixed to 9600 baud.
Temperature: read out of the built in temperature sensor (no ...
Read More...
Features
INDI SBIG driver supports all SBIG family of CCDs/Guider and Filter wheels. Both USB & Parallel Port versions are supported. Mono and color CCDs are fully supported as well. INDI SBIG drivers are available for x86 and ARM architectures in bo ...
Read More...
Features
INDI SBIG driver supports all SBIG family of CCDs/Guider and Filter wheels. Both USB & Parallel Port versions are supported. Mono and color CCDs are fully supported as well. INDI SBIG drivers are available for x86 and ARM architectures in b ...
Read More...
ScopeDome controller can be used with a classic observatory dome and also roll-off roof, but the driver has only been tested with a dome so far.
Features
ScopeDome is a fully automatic observatory dome control system. It also has a variety of sensors an ...
Read More...
The Seletek is a peripheral controller developed by Lunático. This version of the driver allows to control its basic sensors and one or two focuser (three in the Platypus version) connected to the Seletek. You can check all the details about the driver an ...
Read More...
